- 您现在的位置：买卖IC网 > Sheet目录290 > 5.05.01 FLASHER 5 (Segger Microcontroller Systems)PROGRAMMING TOOL FOR MCU
ASCII command interface to Flasher V2.00
Segger Microcontroller GmbH & CoKG
#AUTO NOINFO
This command may be used instead of AUTO, if no status messages from Flasher should be sent
during execution.
The command ends with #OK or #ERRxxx
#BLANK
This command can be sent to perform a blank check over all selected target Flash sectors.
Flasher will reply the following sequence of messages:
#ACK
#STATUS:START CMD
#STATUS:CONNECTING
#STATUS:RESET
#STATUS:CONNECTING
#STATUS:BLANK CHECK
#STATUS:READY
#OK
in case of blank check failure, Flasher will respond with
#ERR004:BLANK CHECK FAILED .
#CLEAR
This command can be sent to clear all selected target Flash sectors.
Flasher will reply the following sequence of messages:
#ACK
#STATUS:START CMD
#STATUS:CONNECTING
#STATUS:RESET
#STATUS:CONNECTING
#STATUS:CLEARING
#STATUS:READY
#OK
in case of an erase failure, Flasher will respond with
#ERR001:ERASE FAILED .
or an other error message if any communication error occured.
#CLEARALL
This command can be used with Flasher ST7 to remove the read out protection of ST7 target CPUs.
The read out protection is removed and the whole target Flash area is erased.
#START
This command can be sent to release Flashers target interface. All signals from Flasher to target will
be set into high-Z mode, reset of target will be released. May be used to start target application pro-
gram.
Flasher will reply the following sequence of messages:
#ACK
#STATUS:START CMD
#STATUS:READY
#OK
#CRC
This command is useful to identify or verify Flashers internal data which should be programmed to
target CPU.
Flasher responds with the CRC of its current memory content:
? #CRC:xxxx if data is present. xxxx is a 4 digit HEX number.
?
#CRC:---- if no valid data is present in Flashers memory
#STATUS
This command can be sent any time, even during other command execution. Flasher responds with its
current state. All defined state messages are described under “Flasher reply messages from Flasher”
later on in this manual.
? 2004 – 2012 Segger Microcontroller GmbH & CoKG
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
5.09.01 FLASHER STM 8
PROGRAMMING TOOL FOR STM8
5-103948-7
2X8 MTE SHRD PIN SR LTCH .100
5-103953-4
4X5 MTE PIN SR RIBBED .100CL
5-103955-4
4X5 MTE PIN SR RIBBED .100CL
5-103968-2
8X3 MTE RCPT SR RIBBED .1010CL
5-103970-3
5X4 MTE RCPT SR RIBBED .100CL
5-103973-9
2X10 MTE RCPT SR RIBBED .100CL
5-103975-8
2X9 MTE RCPT SR PLAIN .100CL
相关代理商/技术参数
5.05.01
制造商:SEGGER 功能描述:FLASH PROG M16C M32C R8C M38000 & ST
5.05.10 FLASHER 5 PRO
制造商:Seggar Embedded Software Solutions 功能描述:TOOL PROGRAMMING RENESAS MCU 制造商:SEGGER 功能描述:PROGRAMMER, M16C/32C, M79, R32C, R8C MCU, Silicon Family Name:M16C, M32C, R32C, R8C, Core Architecture:M16C, M32C, R32C, R8C, Core Sub-Architecture:M16C, M32C, R32C, R8C, IC Product Type:Programmer
5.05.510.359/1303
制造商:Rafi 功能描述:Bulk
5.05.510.421/0000
制造商:C&K Components 功能描述:RAFIX 16 PUSHBUTTON, FLUSH LENS, SQUARE COLLAR 制造商:RAFI 功能描述:CONNECTOR MULTIPOLE
5.05.510.470/1002
制造商:RAFI 功能描述:LENS ACTUATOR TRANSPARENT CLEAR 制造商:RAFI 功能描述:LENS, ACTUATOR, TRANSPARENT, CLEAR 制造商:RAFI 功能描述:LENS, ACTUATOR, TRANSPARENT, CLEAR; For Use With:8mm Series illuminated Pushbutton Switches; Lens Colour:Clear; Lens Diameter:8mm; Colour:transparent clear; External Diameter:8mm ;RoHS Compliant: Yes
5.05.510.470/1303
制造商:Rafi 功能描述:Bulk 制造商:RAFI 功能描述:LENS TRANSPARENT RED
5.05.510.470/1402
制造商:RAFI 功能描述:LENS TRANSPARENT YELLOW
5.05.510.470/1502
制造商:RAFI 功能描述:LENS TRANSPARENT GREEN 制造商:RAFI 功能描述:LENS, TRANSPARENT GREEN 制造商:RAFI 功能描述:LENS, TRANSPARENT GREEN; For Use With:8mm Series illuminated Pushbutton Switches; Lens Colour:Green; Lens Diameter:8mm; Colour:Transparent Green; External Diameter:8mm ;RoHS Compliant: Yes